- Fluval 207 vs 307: What’s The Difference?
- What Size Canister Filter Do I Need?
- Fluval 207 and 307: Detailed Comparison
- Maintenance and Cleaning
- Pump Performance and Efficiency
- Filter Noise
- Conclusion – Fluval 207 or 307, Which Should You Buy?
I’ve become a massive fan of Fluval products in the time I’ve been keeping fish, so when I was looking to purchase a new external filter for (yet another) tank I was setting up, it was no surprise I went with the Fluval 07 series.
In this article, we’ll dive into an in-depth comparison of these two models, highlighting their key differences to help you decide which is the right one for your home aquarium.
I own a 307 and a 407 filter and I’m super happy with both of them. I will share with you my thoughts, and experiences, and include some handy tips as all of this can be applied to the entire 07 series.
Which 07 canister filter is right for you will depend on a few factors:
- Tank size
- Type of fish you have
- Do you have an overstocked aquarium?
Fluval 207 vs 307: What’s The Difference?
An in-depth comparison isn’t for everyone, so for those of you who want the TL;DR version, here’s an overview of what each filter offers:
You may notice my tank size suitability figures differ slightly from what Fluval state, I’ve done a chart further down explaining how I work this out.
|FLUVAL 207||FLUVAL 307|
|Tank Size||Up to 40 Gallons (150 Liters)||Up to 60 Gallons (227 Litres)|
|Pump Output||206 G/ph (780 L/h)||303 G/ph (1,150 L/h)|
|Filter Media Capacity||3 baskets holding 0.5 gallons (1.8 liters)||3 baskets holding 0.8 gallons (3.1 liters)|
|Power Consumption||120V – 10 Watts / 230-240V – 10 Watts||120V – 16 Watts / 230-240V – 15 Watts|
|Annual Running Cost (Approx)||$10.51||$16.82|
|Dimensions||H 16.5” x L 7.5” x W 7”||H 16.5” x L 9.5” x W 7”|
|Filter Media Included||2 x Bio-Foam Max pads, 2 x Bio-Foam pads, 1 x Bio-Foam + pad, 1 x bag carbon, 1 x bag BioMax rings, and 1 x Quick Clear pad||2 x Bio-Foam Max pads, 2 x Bio-Foam pads, 2 x Bio-Foam + pads, 2 x bags carbon, 2 x bags BioMax rings, and 2 x Quick Clear pads|
The entire 07 series filters are a breeze to set up and maintain (details and tips on how to do this further down).
So, what it comes down to is:
- Tank size: The Fluval 207 canister filter is suited for tanks up to 40 gallons (150 liters), while the Fluval 307 is designed for tanks up to 60 gallons (227 liters).
- Size: Both filters are the same height, but the Fluval 307 is 2” longer than the 207, so if you’re tight on space you may struggle to fit it beneath an aquarium.
- Filtration capacity: The Fluval 307 offers a higher filtration capacity with a circulation rate of 303 gallons per hour compared to the 207’s 206 gallons per hour.
- Energy efficiency: Both the 207 and 307 are super energy-efficient options that can potentially save you money on your bills in the long run.
Based on a cost of $0.12 per kWh, the runnings costs for each filter are:
Fluval 207 = $10.51 per year.
Fluval 307 = $16.82 per year.
- Tank Stocking Levels: If you have a heavily stocked tank, it’s best to choose a more powerful filter to keep the water clean and clear. Use the chart below to work out what flow rate you need for your setup.
What Size Canister Filter Do I Need?
A general rule of thumb is that you want the pump output (gallons per hour) to be 5 times the size of your tank, so multiply the size of your tank by 5 to find out the g/ph that is ideal.
I’ve found that following this simple calculation stops you from buying a filter that is too small or too large (and wasting money) for your aquarium.
If you have an overstocked stocked tank that has a large bioload, it’s recommended that you multiply your tank size in gallons by 10, to find a suitable turnover rate for your tank.
Since there is no standardized calculation used by all the different manufacturers, each manufacturer may suggest a different tank size suitability for their ‘XXX g/ph’ filter.
By using this formula, you can compare filters from different manufacturers on an equal basis.
|TANK SIZE (GALLONS)||NORMAL STOCKING LEVELS||HEAVILY STOCKED TANK|
|20||100 g/ph||200 g/ph|
|29||145 g/ph||290 g/ph|
|40||200 g/ph||400 g/ph|
|55||275 g/ph||550 g/ph|
|75||375 g/ph||750 g/ph|
|90||450 g/ph||900 g/ph|
|100||500 g/ph||1000 g/ph|
Most manufacturers state the g/ph when the filter is empty with no media in place.
Once the media is in place (and it’s got gunked up after a while!), these g/ph figures reduce drastically and the real-world turnover rate will probably be around 50% less.
Nonetheless, I’ve found on the whole that the filtration based on this calculation is more than adequate.
Fluval 207 and 307: Detailed Comparison
Now for those of you who like to know every last detail, grab yourself a cup of coffee and get comfortable. We’ll dive into all the differences and go over how to set up and maintain these filters, with some handy tips included along the way.
The Fluval 207 is suitable for aquariums of up to 40 gallons (150 liters).
The Fluval 307 is suitable for aquariums of up to 60 gallons (227 liters).
The 07 series also has smaller and larger filters available the Fluval 107 and 407.
Type Of Fish You Keep
Different fish require different levels of filtration. Some fish are particularly messy so you need to make sure your filter can cope with them.
I’ll list a few common messy fish and if you keep any of these guys you may be best choosing the 307 because it has more capacity for filter media to help catch the additional mess, to keep your water clean and clear.
Bristlenosed Pleco – Although these guys are part of a tank’s clean-up crew and do a great job of eating algae and leftover food, all that algae and food have to come out the other end!
Cichlids – In particular large cichlids like Oscars, who are known to rip up plants, stir up the substrate, and even re-arrange rocks, all creating lots of mess.
Goldfish – These guys love to dig around and stir up the substrate and are known for pooping a lot, so you need a filter that can cope.
Turtle – If you keep a turtle not fish in your aquarium, you will need a much more powerful filter to deal with the amount of waste they produce, check out my turtle filter guide for more info.
Freshwater and Saltwater Compatibility
Both the Fluval 207 and 307 external canister filters are designed to work in freshwater and saltwater aquariums.
Both filters come with filter media included, consisting of mechanical, biological, and chemical filtration.
The 307 comes with 1 extra of the following:
- Bio-Foam + pad
- Bag of carbon
- Bag of BioMax rings
- Quick Clear pad
The included Quick Clear and Bio-Foam + pads are not transferable between the 2 filters.
Mechanical Filtration Media
Mechanical media catches all of the debris in the water, if you’ve got loads of stuff floating around in the water, it’s time to rinse out those filter pads!
The Bio-foam, Bio-foam Max, Quick-clear, and Bio-foam + pads do a great job of catching all the nasty stuff.
Biological Filtration Media
Biological filtration uses beneficial bacteria to consume highly toxic ammonia and nitrites, turning it into safer nitrate, which you then reduce with water changes and by having live plants.
Beneficial bacteria grow on all surfaces in your aquarium, so the more surface area you can provide the better, having the additional basket in the 307 really helps here, especially in a heavily stocked aquarium.
Bio-max rings provide valuable extra surface area for beneficial bacteria to colonize, aiding in breaking down these harmful toxins, and keeping your nitrogen cycle in check, helping keep the water safe for your fish.
Chemical Filtration Media
Activated carbon helps remove chemical impurities, odors, and discoloration from the water, keeping it crystal clear and smelling sweet, no one wants their tank to smell like rotten eggs!
Activated carbon needs to be replaced on a regular basis as it will stop working, aim to replace it after a month.
Important: Carbon also removes medications, so remove all activated carbon filter media when treating your fish with medication.
Fluval 207 And 307 Setup and Installation
Setting up both of these 07 series canister filters is the same process, I’ll also include a video as I find it’s easier to watch a video before reading an explanation, to help everything make more sense.
One thing I really like about the Fluval 07 series filters is that setting them up is a breeze. One thing to note is it’s important to put your filter media in the correct baskets (see image below).
You want the water to pass through the mechanical filtration first (coarse first, then finer media), then through the biological filtration, and finally through the optional chemical filtration.
Although they arrive assembled, you have to take it all apart as there’s a leaflet inside the canister, the filter media comes sealed in plastic bags, as does the rubber gasket seal that goes between the canister and lid.
The ceramic rings can get a bit dusty during shipping, so make sure you rinse them thoroughly to get all of the dust off them.
If you have a heavily planted tank, you may want to avoid using activated carbon as it will filter out the nutrients in the water that your plants thrive off, it will also soak up any plant fertilizer you add. If you find your plants starting to look unhealthy, this could be the culprit.
You could fill the top media basket with some extra ceramic rings instead, giving plenty of additional surface area for beneficial bacteria to grow.
Putting it back together is the exact reverse of taking it apart.
Inside the canister are tracks molded into the sides to form different compartments. The filter media baskets and frame that hold the Bio-foam and Bio-foam Max pads will only fit back inside one way.
TOP TIP: When you’ve put the Bio-foam+ and quick clear pads back in the bottom tray put the red lifting handle through the basket at this point.
It’s much easier to then stack the rest of the baskets on top of each other with the handle in place rather than inserting the handle once you’ve stacked the baskets on top of each other…..Yes, I learned the hard way!
Install the rubber gasket on the filter lid.
Like the baskets, the canister lid will only fit one way too. The 207 or 307 badge on the front of the lid fits into a notch molded into the rim of the canister body.
The hose clamps do a great job of keeping the intake and output hoses in place and are a much better design than those on the FX4 and FX6 filters.
When it comes to fitting the hose clamps to your tank, all I’ll say is: read the instructions first (or watch the YT video above)…I’m a typical guy, instruction manuals must not be read at all costs, I will struggle and tear my hair out first!!
Basically, the fittings have 2 parts: the clamp that fits onto the tank and the cover that secures the piping in place.
The covers need to be fitted vertically. The rear part of the clamp and the pipe cover slide together using tongue and groove moldings. The underside of the curved part of the cover then clips onto the curved part of the clamp.
The Aquastop valve is a key feature of the 07 canister filter range.
This valve allows you to stop the water flow and then detach it from the filter in one piece, making cleaning and maintenance waaaaaaaay easier.
To install the Aquastop valve:
- Place the Aqua stop valve on the inlet and outlet ports on the top of your canister filter and press the red lever down to lock it in position.
- Lift the grey lever up so it’s vertical to put the valve in the OFF position.
Place the filter on a flat and sturdy surface, beneath your fish tank.
Canister filters are ‘gravity fed’ so they need to be below the tank for them to work correctly. If you put a canister filter at the side of a tank, the top of the filter must be below the surface of the water, but it can be tricky to get the filter working efficiently.
Position the filter as close to your aquarium as you can and avoid any sharp bends or turns in the tubing.
Fit The Tubing
The included hardware comes in different sizes between the 207 and 307, but fitting it is the same procedure.
The intake and output hose is supplied in a single length that you have to cut yourself.
To avoid miscutting my pipe the wrong length (come on, we’ve all done it!) I find it easier to attach both ends of the pipe to the filter valves at this point, then cut it once I know it will reach over the top of the tank and back into the water.
If you do miscut the tubing, it’s not the end of the world, you can get a replacement length of tube, but they use different sizes, so make sure you get the correct size.
You’ll need to take into account the length of the intake assembly when trimming the intake pipe:
- The 207’s intake assembly is 10.5” (26.5cm) in length
- The 307’s intake assembly is 13.75” (35cm) in length
The Aquastop valve is clearly marked which side is the intake and outlet so you can’t get this wrong.
The output nozzle does a decent job itself, but you can add the Fluval Spray Bar Kit, to help eliminate surface scum and aerate the water.
To prime the pump:
- Ensure your output nozzle is above the water’s surface so it has access to air.
- Press the grey lever on the Aquastop valve downwards so it sits on top of the red lever.
- Move the priming handle up and down 3 or 4 times until you can hear the filter filling itself with water.
Once the canister filter has filled with water, plug it into the mains power and you should have water flowing out of the outlet nozzle.
I always recommend having a drip loop on all electrical items for your aquarium, we all know water and electricity are not a good match!
That’s it, you’re all set up and good to go.
Maintenance and Cleaning
It is the same process for cleaning both Fluval 207 and 307.
The only thing missing from the Fluval filters is a handle like the Oase Biomaster filters have, a simple thing that makes life easier….but it’s not a deal breaker!
- Disconnect the filter from the aquarium and unplug: Lift the grey lever on the Aquastop valve so it’s vertical, this puts it into the off position and stops the flow of water. Unplug from mains power. Lift the red lever to disconnect the Aquastop valve from the filter.
- Put a towel and bucket on the floor and empty the water from the filter into the bucket, you’ll then use this water to clean everything.
- Remove the filter lid by pulling the grey lift-lock motor head clamps outwards and then push down on them until the lid releases.
- The EZ-Lift media baskets can be removed with one finger using the red handle.
Clean the mechanical filter media: Gently squeeze the sponge or foam media in the bucket to remove larger debris and waste particles, you don’t need to get them spotless.
Inspect and rinse the biological media: Check the ceramic rings or bio-balls for any accumulated debris and gently swish them in the same bucket to remove surface dirt.
Replace the chemical filter media as needed: Chemical media has a limited lifespan and should be replaced according to the manufacturer’s recommendations or when you notice a decline in water quality.
Top Tip: Use the water in the bucket that you rinsed all the filter media in to water your house plants or garden, your plants will love it!
- Clean the filter’s impeller and housing: Over time, debris and slime can accumulate in this area, resulting in reduced pump performance.
The impeller is located under the red cover on the underside of the lid. Remove the impeller and gently clean it in the bucket and wipe out the housing where the impeller sits with a cloth.
- Clean the main body of the canister where the filters go: Add a bit of water and swish it around to loosen any brown sludge in the bottom and pour it into the bucket.
- Finally, using a bottle brush clean the input and output nozzles to remove any buildup or debris. These nozzles pull apart easily so you can get into all the nooks and crannies.
- Reassemble and reconnect the filter: Once everything has been cleaned, reassemble the media baskets, fit the lid, and reconnect the pipes by pulling down the red lever and then the grey lever, you will hear a flow of water as your filter re-fills (if you don’t hear water flowing, pump the primer a few times).
- Once your filter has filled up plug it back into the mains power.
Never use soaps or detergents to clean your filter (or aquarium).
Top Tip: When you put the lid back on, push it down firmly all the way around before clipping the grey brackets in place, this ensures you have a nice tight water seal and avoids any leaks.
You will need to lubricate the rubber o-ring occasionally using a silicone based lubricant.
Pump Performance and Efficiency
When you’re looking to choose a new canister filter, the filter’s pump performance and energy consumption are important things to consider with the ever-increasing cost of living.
Pump Output and Circulation
The Fluval 207 has a circulation rate of 206 gallons per hour (780 L/h), making it suitable for aquariums of up to 40 gallons.
On the other hand, the Fluval 307 has a filter circulation rate of 303 Gal/h (1,150 L/h), making it suitable for aquariums of up to 60 gallons, or for a heavily stocked smaller aquarium.
With ever-rising energy prices, this has to be something to take into consideration.
Both Fluval 207 and 307 filters excel in energy efficiency, consuming 25% less power compared to their predecessors (the Fluval 06 canister filters) while still providing great performance.
The 207’s power consumption is 120V – 10 Watts / 230-240V – 10 Watts.
The 307’s power consumption is 120V – 16 Watts / 230-240V – 15 Watts.
According to the energy.gov website (at the time of writing) the annual running cost of each filter is:
- Fluval 207 at the US Average of $0.12 per kWh = $10.51 per year.
- Fluval 307 at the US Average of $0.12 per kWh = $16.82 per year.
In terms of noise, all 07 series filters are quiet when running. I’m really sensitive to background noises, the slightest little thing drives me nuts if I’m trying to read or watch TV.
When I tested my 407, it came in at 48 decibels (right next to it) using the noise app on my Apple Watch.
I expect the 207 to have similar noise levels.
The 207 is the smaller of the 2 filters so is a little more budget-friendly.
Conclusion – Fluval 207 or 307, Which Should You Buy?
I’m super happy with both of my 07 series filters and can highly recommend them, they’re reliable, quiet, and cheap to run, so which should you buy?
If you have an aquarium of up to 40 gallons, buy the 207.
If you have an aquarium that is 40-60 gallons, buy the 307.